Linux version 2.6.24-gentoo-r3 (root@localhost) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #4 SMP Sat Mar 22 20:46:45 WET 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001bf70000 (usable) BIOS-e820: 000000001bf70000 - 000000001bf7f000 (ACPI data) BIOS-e820: 000000001bf7f000 - 000000001bf80000 (ACPI NVS) BIOS-e820: 000000001bf80000 - 000000001c000000 (reserved) BIOS-e820: 000000002bf80000 - 000000002c000000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 447MB LOWMEM available. Entering add_active_range(0, 0, 114544) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 114544 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 114544 On node 0 totalpages: 114544 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 862 pages used for memmap Normal zone: 109586 pages, LIFO batch:31 Movable zone: 0 pages used for memmap DMI 2.3 present. ACPI: RSDP 000F6C70, 0014 (r0 PTLTD ) ACPI: RSDT 1BF783FD, 002C (r1 PTLTD RSDT 6040000 LTP 0) ACPI: FACP 1BF7EF64, 0074 (r1 ATI Salmon 6040000 ATI F4240) ACPI: DSDT 1BF78429, 6B3B (r1 ATI MS2_1535 6040000 MSFT 100000E) ACPI: FACS 1BF7FFC0, 0040 ACPI: BOOT 1BF7EFD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: DMI detected: Hewlett-Packard ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 Allocating PCI resources starting at 30000000 (gap: 2c000000:d3f80000) Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113650 Kernel command line: Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffb000 (0138b000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 2525.298 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 447540k/458176k available (2631k kernel code, 10024k reserved, 918k data, 252k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB) vmalloc : 0xdc800000 - 0xfffb3000 ( 567 MB) lowmem : 0xc0000000 - 0xdbf70000 ( 447 MB) .init : 0xc047e000 - 0xc04bd000 ( 252 kB) .data : 0xc0391c48 - 0xc047765c ( 918 kB) .text : 0xc0100000 - 0xc0391c48 (2631 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5054.80 BogoMIPS (lpj=2527400) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Hyper-Threading is disabled CPU: After all inits, caps: bfebf9ff 00000000 00000000 0000b080 00004400 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 14k freed ACPI: Core revision 20070126 ACPI: setting ELCR to 0200 (from 0420) CPU0: Intel(R) Pentium(R) 4 CPU 2.53GHz stepping 07 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs net_namespace: 64 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd88b, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using PIC for interrupt routing ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62 ACPI: EC: driver started in poll mode ACPI: PCI Root Bridge [PCI0] (0000:00) PCI quirk: region 8000-803f claimed by ali7101 ACPI PCI quirk: region 8040-805f claimed by ali7101 SMB ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: PCI Interrupt Link [LNK0] (IRQs 7 10) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 7 *10) ACPI: PCI Interrupt Link [LNK2] (IRQs 7 10) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 7 10) *0, disabled. ACPI: PCI Interrupt Link [LNK4] (IRQs 7 *10) ACPI: PCI Interrupt Link [LNK5] (IRQs 7 *11) ACPI: PCI Interrupt Link [LNK6] (IRQs 7 10) *0, disabled. ACPI: PCI Interrupt Link [LNK7] (IRQs *5) ACPI: PCI Interrupt Link [LNK8] (IRQs 7 *10) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Time: tsc clocksource has been installed. system 00:07: ioport range 0x40b-0x40b has been reserved system 00:07: ioport range 0x480-0x48f has been reserved system 00:07: ioport range 0x4d0-0x4d1 has been reserved system 00:07: ioport range 0x4d6-0x4d6 has been reserved system 00:07: ioport range 0x8000-0x807f could not be reserved system 00:07: ioport range 0xff00-0xff01 has been reserved system 00:07: ioport range 0x8004-0x8005 has been reserved system 00:07: ioport range 0xfe00-0xfefe has been reserved system 00:07: iomem range 0xd000b000-0xd000bfff has been reserved PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: d0300000-d03fffff PREFETCH window: d8000000-dfffffff PCI: Bus 2, cardbus bridge: 0000:00:0a.0 IO window: 00001800-000018ff IO window: 00001c00-00001cff PREFETCH window: 30000000-33ffffff MEM window: 34000000-37ffffff PCI: Enabling device 0000:00:0a.0 (0005 -> 0007) ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd Freeing initrd memory: 1950k freed Simple Boot Flag at 0x37 set to 0x1 Machine check exception polling timer started. Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.29 [Flags: R/O]. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Activating ISA DMA hang workarounds. Boot video device is 0000:01:05.0 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using get_cycles(). ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery absent) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] input: Lid Switch as /class/input/input2 ACPI: Lid Switch [LID] ACPI: EC: non-query interrupt received, switching to interrupt mode ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Thermal Zone [THRM] (36 C) Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10 natsemi eth0: NatSemi DP8381[56] at 0xd000a000 (0000:00:12.0), 00:0b:cd:35:4e:2b, IRQ 10, port TP. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc4) at PCI slot 0000:00:10.0 ACPI: Unable to derive IRQ for device 0000:00:10.0 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: IC25N040ATCS04-0, ATA DISK drive hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 hda: UDMA/100 mode selected ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: TOSHIBA DVD-ROM SD-R2312, ATAPI CD/DVD-ROM drive hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4 hdc: MWDMA2 mode selected ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 78140160 sectors (40007 MB) w/1768KiB Cache, CHS=65535/16/63 hda: cache flushes not supported hda: hda1 hda2 < hda5 hda6 hda7 > hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods usbmon: debugfs is not available ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd: block sizes: ed 64 td 64 ACPI: PCI Interrupt Link [LNK8] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNK8] -> GSI 10 (level, low) -> IRQ 10 ohci_hcd 0000:00:02.0: OHCI Host Controller drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: created debug files ohci_hcd 0000:00:02.0: irq 10, io mem 0xd0000000 ohci_hcd 0000:00:02.0: enabling initreset quirk ohci_hcd 0000:00:02.0: OHCI controller state ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:02.0: control 0x083 HCFS=operational CBSR=3 ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF ohci_hcd 0000:00:02.0: intrenable 0x8000004a MIE RHSC RD WDH ohci_hcd 0000:00:02.0: hcca frame #0005 ohci_hcd 0000:00:02.0: roothub.a 02000203 POTPGT=2 NPS NDP=3(3) ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS usb usb1: default language 0x0409 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: global over-current protection hub 1-0:1.0: power on to power good time: 4ms hub 1-0:1.0: local power source is good hub 1-0:1.0: no over-current condition exists hub 1-0:1.0: trying to enable port power on non-switchable hub hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.24-gentoo-r3 ohci_hcd usb usb1: SerialNumber: 0000:00:02.0 ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNK4] -> GSI 10 (level, low) -> IRQ 10 ohci_hcd 0000:00:0f.0: OHCI Host Controller drivers/usb/core/inode.c: creating file '002' ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0f.0: created debug files ohci_hcd 0000:00:0f.0: irq 10, io mem 0xd0009000 ohci_hcd 0000:00:0f.0: enabling initreset quirk ohci_hcd 0000:00:0f.0: OHCI controller state ohci_hcd 0000:00:0f.0: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:0f.0: control 0x083 HCFS=operational CBSR=3 ohci_hcd 0000:00:0f.0: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:0f.0: intrstatus 0x00000004 SF ohci_hcd 0000:00:0f.0: intrenable 0x8000004a MIE RHSC RD WDH ohci_hcd 0000:00:0f.0: hcca frame #0005 ohci_hcd 0000:00:0f.0: roothub.a 02000203 POTPGT=2 NPS NDP=3(3) ohci_hcd 0000:00:0f.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:0f.0: roothub.status 00008000 DRWE ohci_hcd 0000:00:0f.0: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:0f.0: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:0f.0: roothub.portstatus [2] 0x00000100 PPS usb usb2: default language 0x0409 usb usb2: uevent usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: global over-current protection hub 2-0:1.0: power on to power good time: 4ms hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: trying to enable port power on non-switchable hub hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.24-gentoo-r3 ohci_hcd usb usb2: SerialNumber: 0000:00:0f.0 USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 cpuidle: using governor ladder usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. Using IPI Shortcut mode Marking TSC unstable due to: TSC halts in idle. Time: acpi_pm clocksource has been installed. Synaptics Touchpad, model: 1, fw: 5.8, id: 0x2348b3, caps: 0x904713/0x10008 input: SynPS/2 Synaptics TouchPad as /class/input/input4 RAMDISK: Couldn't find valid RAM disk image starting at 0. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 252k freed usb usb1: uevent usb 1-0:1.0: uevent usb usb2: uevent usb 2-0:1.0: uevent udev: renamed network interface eth0 to eth1 PCI: Enabling device 0000:00:06.0 (0005 -> 0007) ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNK7] -> GSI 5 (level, low) -> IRQ 5 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A AC'97 1 does not respond - RESET AC'97 1 access is not valid [0xffffffff], removing mixer. ali mixer 1 creating error. Yenta: CardBus bridge found at 0000:00:0a.0 [103c:0850] Yenta O2: res at 0x94/0xD4: 00/ea Yenta O2: enabling read prefetch/write burst Yenta: ISA IRQ mask 0x0098, PCI irq 11 Socket status: 30000007 PCI: Enabling device 0000:00:08.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNK6] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt for device 0000:00:08.0 disabled EXT3 FS on hda7, internal journal Linux agpgart interface v0.102 agpgart: Detected Ati IGP345M chipset agpgart: AGP aperture is 64M @ 0xd4000000 [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10 ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0] -> GSI 10 (level, low) -> IRQ 10 [drm] Initialized radeon 1.28.0 20060524 on minor 0 NTFS volume version 3.1. Adding 506008k swap on /dev/hda6. Priority:-1 extents:1 across:506008k hda: UDMA/100 mode selected hdc: MWDMA2 mode selected